Short answer. Winterizing means getting the water out, or replacing it with enough of the right antifreeze to protect against the lowest temperature your boat might see. BoatUS says fresh water expands about 9 percent when it freezes, and that an analysis of ten years of GEICO | BoatU.S. freeze claims found that more than three-quarters involved cracks in the engine block or exhaust manifolds because water was left in the engine or cooling system. Unless you are in Hawaii or the Florida Keys, BoatUS recommends winterizing the engine if you will lay the boat up for even a few weeks.[1]
Use this checklist as a starting point, then follow the owner's manuals for the engines, generator and other systems on your boat. Procedures differ by model. If the engine is still under warranty, BoatUS warns that skipping the manufacturer's winterizing instructions can void coverage.[1]
Before you start
- Read the manuals. BoatUS says to consult the engine owner's or service manual before you begin, especially on outboards and sterndrives, which vary by type.[1] Mercury and Yamaha say the same for their outboards.[2][3]
- Get a written yard contract if someone else is doing the work. BoatUS says "winterizing" has no universal meaning. List every job, including the heads, seacocks and freshwater system, and set a start date well before the first typical hard freeze. Do not assume the yard will inspect docklines and the bilge unless you pay for that service.[1]
- Do not rely on a heater instead of winterizing. BoatUS says a heater is no substitute, and its claim files include boats that froze when the power went out, or that caught fire from a damaged extension cord or the heater itself.[1]
- Use the right antifreeze in the right place. For drinking-water and raw-water systems, BoatUS says to use non-toxic propylene glycol, not engine coolant (ethylene glycol), which is highly toxic and must never go in a freshwater system. In a closed freshwater-cooling loop, BoatUS says the year-round coolant is typically a 50/50 mix; do not go richer than 50 percent, because a too-rich mix can congeal (100 percent coolant turns to a solid gel at −8°F). Winterizing antifreeze labeled −50°F may only protect PVC pipes from bursting down to about −10°F and can begin freezing around 15°F above zero. Use it full strength unless the label says otherwise, and keep pumping until the antifreeze has displaced the water already in the system.[1]
- Work clean. BoatUS's green-winterizing notes: capture antifreeze if you can, put an oil-only absorbent pad under engine work, temporarily plug scuppers and disable the bilge pump while you work (then turn the bilge pump back on), and recycle used oil and antifreeze properly.[1]
If you store the boat ashore
BoatUS's claim files suggest a boat is less likely to be damaged, in the short and the long run, if it is left on land rather than in the water, but boats ashore must be winterized earlier because air temperatures drop sooner than water temperatures. Support the hull properly: use a cradle made for that model, or jackstands (at least three per side on boats over 26 feet) with plywood under the bases and safety chains, plus wide keel blocks. After blocking, sight along the hull and check again in about two weeks. For outboard and sterndrive boats, BoatUS says to take weight off the transom by lowering the drive units onto a block.[1]
If you leave the boat in the water
- Close all seacocks except cockpit drains. If a below-waterline thru-hull cannot be closed, BoatUS says the boat should be stored ashore. After closing a seacock, remove the hose so it drains, take out residual water, then reinstall the hose with two stainless hose clamps where possible.[1]
- Plug exhaust ports, and remember to remove the plugs in the spring. BoatUS notes claims in which muskrats chewed through an exhaust system and sank the boat.[1]
- Adjust a dripping stuffing box until the drip stops. Check rudder stuffing boxes too.[1]
- Wire the bilge pump directly to the batteries with a fuse so it still runs when the panel is off. Clean the bilge, confirm the pump and switch work, then add enough non-toxic antifreeze to trip the float switch and sponge out the rest.[1]
- Center the boat in the slip, use long docklines and spring lines, and add chafe guards. Check lines and fenders.[1]
Engines: three steps that apply to every type
BoatUS lists three essentials for any engine:[1]
- Change the oil and oil filter just before lay-up. Residual acids and moisture left in the crankcase over the winter can pit bearings. Run the engine briefly first so the oil is warm and has picked up impurities, change the oil and filter, then run about a minute to circulate the fresh oil and check the filter for leaks.
- Change the fuel filter and stabilize the fuel. For gasoline with ethanol (E10), BoatUS says phase separation can only be completely prevented by emptying the tank. If that is not practical, add stabilizer and fill the tank to about 95 percent full to allow for expansion. Check the new filter for leaks while the engine is running.
- Get the water out of the engine, or fill the raw-water side with antifreeze. This is the step BoatUS says is behind the vast majority of its freeze claims. How you do it depends on the engine, below.
Gas sterndrive or inboard
Follow the inboard or sterndrive section of the BoatUS guide, plus your manual.[1]
Closed cooling (the freshwater side). With the engine at room temperature, slowly remove the expansion-tank cap and check the mix with an antifreeze hydrometer. If the coolant is rusty or dirty, drain it and replace it with a fresh 50/50 mix. The raw-water side still has to be winterized separately.[1]
Raw-water side: circulating antifreeze (BoatUS's preferred method for inboards). Bring a raw-water-cooled engine up to operating temperature so the thermostat is open; otherwise antifreeze can skip some passages. In cold weather you may need to remove the thermostat (reinstall it in the spring with a new gasket). Then:[1]
- If the boat is in the water, close the intake seacock.
- Fill a five-gallon bucket with undiluted non-toxic antifreeze, with more on hand if the engine takes more than that.
- Remove the raw-water intake hose from the seacock and put the end in the bucket.
- Start the engine and idle until antifreeze has discharged from the exhaust for 30 seconds or more.
- On gasoline engines, fog the cylinders (see below), which should stop the engine.
- Secure the intake hose back on the seacock.
If you cannot reach that hose, BoatUS mentions purpose-made valves, funnels and reservoirs, but only if the antifreeze reaches everything downstream of where you add it.[1]
Draining instead. If your manual says to drain, BoatUS says you must be thorough: open every petcock in the manual, clear any that are clogged, and also drain the sea strainer, seacock body and water-lift muffler if fitted. Small pockets of water can still crack expensive parts, which is why BoatUS prefers circulating antifreeze on inboards.[1]
Fogging a gasoline inboard. Once antifreeze is coming out of the exhaust, turn off the fuel valve if you have one and run the carburetor dry. For the last 10 seconds or so, spray fogging fluid into the flame arrester on the carburetor (or trickle light oil if you have no fogging fluid). After the engine cools, wrap duct tape around the flame arrester, cover the top of the engine with plastic, and leave a tag so you remember to remove the tape in the spring.[1]
Sterndrive (I/O) extras. Some I/Os take cooling water from a thru-hull in the engine compartment; once antifreeze has run through the engine it also protects the outdrive. Other models take water in through the drive and need muffs: warm the engine with muffs, then plumb a five-gallon bucket of antifreeze to the muffs and run the engine until the bucket is empty. Store every outdrive in the down position so water cannot enter the exhaust hub and freeze. Drain and refill the outdrive oil from the bottom fill hole (never from the top vent), and replace plug gaskets. Top up an engine-compartment reservoir if fitted. Inspect or replace anodes. BoatUS also notes that outdrives are a frequent theft target and that some owners remove them for storage.[1]
Diesel inboard
Use the same three essentials and the same raw-water antifreeze (or drain) method as above, following your diesel manual. Do not use the gasoline fogging steps on a diesel; BoatUS's fogging instructions are for gasoline engines.[1]
Also do the BoatUS engine-room checklist items that apply to diesels and to an installed generator:[1]
- Fill fuel tanks (and add stabilizer to gasoline; for diesel, follow the engine maker's fuel advice and your manual).
- Change oil and filter on the engine and on an installed generator.
- Change fuel filters and separators.
- Check the closed-cooling coolant level and mix, and add or replace if needed.
- Run antifreeze through the raw-water system, and make sure water strainers are filled with antifreeze.
- On an installed generator, repeat the oil, fuel-filter, coolant and raw-water antifreeze steps.
If the generator is a Northern Lights unit, Northern Lights also recommends, for long-term storage: change the oil and filter per the genset manual; run the engine up to at least 140°F from a small, clean fuel source dosed with Stabil diesel formula, Stanadyne Performance conditioner, or John Deere fuel-system conditioner if the first two are not available; completely drain, flush and fill the cooling system with pre-mixed 50/50 conventional ethylene-glycol heavy-duty diesel engine coolant; loosen the alternator drive belt; completely seal the intake and exhaust openings with heavy plastic bags, closed at the bottom, with moisture-absorbing desiccant packs inside; and store the engine inside a building, preferably climate-controlled, to prevent corrosion.[4] Follow that unit's manual if it differs.
Related service intervals: Volvo Penta D6, Yanmar 4JH, Yanmar 8LV, Cummins QSB, Cummins QSC8.3, Cummins QSM11, Caterpillar C7/C9, Caterpillar C12, Caterpillar C18, MAN V8-1200. Coolant types: OAT vs conventional. Fuel: diesel bug. Generators: Onan, Kohler, Northern Lights.
Outboard
Consult the manual first. BoatUS says today's engines, especially four-stroke and direct-injected two-stroke outboards, may have special winterizing, flushing and maintenance instructions, and that some newer outboards have an automatic winterizing feature.[1] Mercury and Yamaha also say to follow the owner's manual and the products specified for that engine.[2][3]
Fuel. BoatUS: fill an installed tank and add stabilizer, or drain it completely; empty portable four-stroke tanks into a car tank and take them home.[1] Mercury: store with fresh fuel treated with a marine stabilizer, run the engine about 10 minutes (in the water or on a hose, following the manual) so treated fuel reaches the whole system, then replace the fuel filter. For older vented tanks, Mercury says fill to about 95 percent; it says newer tanks that cannot freely vent do not need to be filled.[2] Yamaha: run stabilizer through the entire system and store the tank 7/8 full; never plug or cap the fuel-tank vent.[3] Where those figures differ, follow your manual.
Flush. BoatUS: flush with muffs and fresh water. Some newer engines have a garden-hose fitting and can be flushed without running; check the manual.[1]
Oil, gear lube and fogging. BoatUS: drain and refill engine oil on four-strokes, drain and refill lower-unit gear lube on all outboards, change fuel filters, then fog. Fogging can be done with the engine running until it smokes and stalls, or with the engine off by spraying oil into the cylinders with the spark plugs removed and turning the flywheel.[1] Mercury: change four-stroke oil and filter every 100 hours or once a season (never use automotive oil in a marine engine); after the change, start the engine again to circulate oil and check for a doubled oil-filter gasket. Fog four-stroke and conventional two-stroke engines while still warm, usually by spraying fogging oil into each cylinder with the plugs out. For Mercury OptiMax and other DFI two-strokes, Mercury says not to use fogging oil; instead squirt one ounce of DFI outboard oil into each cylinder through the spark-plug hole. Change gear lube every 100 hours or once a season; if the old lube is white or creamy, have a dealer pressure-test the gearcase. Inspect the prop shaft for fishing line, grease it, and torque the prop nut to the manual's spec.[2] Yamaha: change the engine oil and the 10-micron fuel filter before storage, fog with the fogging oil specified for that engine (EFI fogging oil for most modern fuel-injected four-strokes; Stor-Rite for two-stroke EFI and carbureted engines), and lube the grease zerks in the manual.[3]
Store the engine so it can drain. BoatUS and Mercury: store the outboard in the lowest, tilted-down (running) position so remaining water can drain; water left in a tilted-up lower unit can freeze and crack the housing.[1][2] Yamaha, for engines stored outside in freezing weather: trim to a full-in, negative trim angle, or place a tightly sealed plastic bag over the lower unit once it is thoroughly dry inside.[3] Follow your manual if those positions differ. Inspect or replace anodes (Mercury: replace sacrificial anodes when they are 50 percent deteriorated).[1][2] Mercury also says to check power-trim fluid (bright red is normal; pink or milky fluid means water in the system), grease the listed fittings, apply a corrosion barrier, and, for a lead-acid battery, top up with distilled water if needed, fully charge it, remove it, and store it in a cool, dry place on a maintenance charger.[2] Yamaha likewise says to charge batteries fully, load-test them, and bring them indoors if the outboard is stored outside in the cold.[3]
Related: outboard four-stroke maintenance, anode selection, marine batteries.
Below decks, other systems, and before you go
From the BoatUS winterizing checklist:[1]
- Pump out the holding tank and add antifreeze to the head (and through a Y-valve if you have one). Close the seacocks. Some head makers, BoatUS notes, advise against non-toxic antifreeze because it may soften gaskets; if you use toxic antifreeze, do not pump it overboard: pump it into a bucket and recycle it.
- Drain the water heater and bypass it, then drain the freshwater system and run non-toxic antifreeze through every hot and cold outlet, working back toward the tank. Drain shower sumps and other places water pools. Run antifreeze through a livewell, washdown pump, refrigeration and watermaker only as those manuals direct.
- For air conditioning, BoatUS prefers removing the raw-water intake, putting the hose in a bucket of non-toxic propylene glycol, and running the pump until antifreeze comes out of the discharge, after cleaning the air and raw-water filters.
- Remove food. Open lockers to air. Take home cushions or store them on their sides. Take home portable electronics and portable propane canisters; close propane valves.
- Verify the bilge pump and switch, clean and dry the bilges, secure ports and hatches, and turn off all circuit breakers except the bilge pump and smoke or vapor alarms.
- Tie off the tiller or wheel, cover or shrinkwrap the boat (BoatUS says leave shrinkwrapping to professionals), lock the cabin, and leave a spare key with the marina manager if that is your arrangement.
- Visit the boat every few weeks, and after storms or hard freezes.
Related: MSD and holding tanks, self-contained air conditioning, watermaker membrane storage, Seakeeper service.
Questions
- When should I winterize the engine?
- BoatUS recommends winterizing the engine if you will lay the boat up for even a few weeks, unless you are in Hawaii or the Florida Keys, so a sudden freeze cannot put it out of commission. Boats stored ashore must be winterized earlier than boats in the water, because air temperatures fall sooner.[1]
- Can I just drain the engine instead of using antifreeze?
- BoatUS describes both methods for the raw-water side, but prefers circulating non-toxic antifreeze on inboards because draining has to be complete and small pockets of water can still crack parts. If you drain, open every petcock in the manual and also drain the sea strainer, seacock body and water-lift muffler.[1]
- What antifreeze should I use?
- In drinking-water and raw-water systems, BoatUS says to use non-toxic propylene glycol, not ethylene glycol engine coolant. In a closed freshwater-cooling system, it describes a typical 50/50 coolant mix and warns against a richer mix. Check the freeze rating carefully; a jug labeled −50°F may begin freezing well above that.[1]
- Do I fog a diesel the same way as a gasoline engine?
- No. BoatUS's fogging steps are written for gasoline engines (and its engine-room checklist says "fog cylinders in gasoline engines"). For a diesel, follow the engine manual for storage oil, fuel and cooling-system steps.[1]
- Should the outdrive or outboard be stored up or down?
- BoatUS says to store outdrives and outboards in the down (lowest) position so water can drain and not freeze in the housing. Mercury says the same for outboards. Yamaha, for outboards stored outside in the cold, says to trim full-in at a negative trim angle, or bag the dry lower unit. Follow your manual when those instructions differ.[1][2][3]
Sources
- BoatUS / GEICO-BoatU.S., The Boater's Guide to Winterizing. https://www.boatus.com/documents/boatus/the-boaters-guide-to-winterizing.pdf (opened 16 Nov 2026).
- Mercury Marine, "How to Winterize Your Outboard". https://www.mercurymarine.com/us/en/lifestyle/dockline/how-to-winterize-your-outboard (opened 16 Nov 2026).
- Yamaha Outboards, "Extended Storage for Your Outboard". https://yamahaoutboards.com/maintenance-matters/extended-storage (opened 16 Nov 2026).
- Northern Lights, "Tips for Winterizing Your Generator". https://www.northern-lights.com/news/winterizing/ (opened 16 Nov 2026; page © Northern Lights, Inc. 2018).