Spring commissioning checklist

Sources checked 16 Nov 2026.

Short answer. Before you launch, go through the boat systematically: hull and running gear, seacocks and hoses, engines and fuel, batteries, and safety equipment. After the boat is in the water, check every thru-hull for leaks. The steps below follow BoatUS's Spring Commissioning Checklist (2022/v3). Federal safety-equipment rules are from the U.S. Coast Guard's November 2023 Boater's Guide. Follow your engine and boat manuals.[1][2]

Pair this list with last fall's winterizing checklist.

Before you launch

From BoatUS:[1]

  • Check the condition of antifouling paint and repaint if necessary.
  • Inspect all hose clamps for rust, and replace as necessary. Double-clamp fuel lines, exhaust hoses, and, if possible, any hoses below the waterline with marine-rated stainless hose clamps. With the exception of scupper or deck drains, keep seacocks closed when you are away from the boat.
  • Inspect all hoses for stiffness, rot, leaks and cracking. Replace any that are faulty. Make sure they fit snugly.
  • Inspect prop(s) for dings, pitting and distortion. Make sure cotter pins are secure. On inboard drive systems, grip the prop and try moving the shaft up and down and side to side. If it is loose and can be wiggled, the cutless bearing may need to be replaced.
  • Check the rudderstock to ensure it has not been bent. Operate the wheel or tiller to ensure the steering works correctly. Check the rudder bearing for unusual play or movement.
  • Inspect the hull for blisters, distortions and stress cracks.
  • Inspect, lubricate and exercise seacocks or thru-hulls.
  • Make sure the engine intake sea strainer is not cracked or bent from ice, is free of corrosion, and is clean and properly secured.
  • On inboards, check the engine shaft and rudder stuffing boxes for correct adjustment. BoatUS says a stuffing box should leak no more than two or three drops each minute when the prop shaft is turning. Check the shaft-log hose for deterioration and rusty hose clamps.
  • Use a garden hose to check for deck leaks at ports and hatches. Renew caulk or gaskets as necessary.
  • Inspect and test the bilge pump and float switch. Inspect the pump hose.
  • Check stove and remote LPG tanks for loose fittings, leaking hoses, and properly functioning shutoff systems. Use the pressure gauge to conduct a leak-down test.
  • Inspect dock and anchor lines for chafe and wear.
  • If equipped, ensure that the stern drain plug is installed.

Related: antifouling types, cutlass bearing diagnostics, packed shaft seal vs PSS, bilge alarm and float switch, ABYC thru-hull bonding.

Engines, outdrives, outboards and fuel

From BoatUS:[1]

  • Inspect rubber outdrive bellows for cracked, dried or deteriorated spots, especially in the folds, and replace if suspect.
  • Check power-steering and power-trim oil levels.
  • Replace anodes that are more than half wasted away.
  • Inspect the outer jacket of control cables. Cracks or swelling indicate corrosion and mean that the cable must be replaced.
  • Inspect lower-unit oil level in sterndrives and outboards and top off as necessary.
  • Inspect fuel lines, including fuel-tank fill and vent hoses, for softness, brittleness or cracking. Check all joints for leaks, and make sure all lines are well supported with noncombustible clips or straps with smooth edges.
  • Inspect fuel tanks, fuel pumps and filters for leaks. Ensure portable tanks and lines are completely drained of stale fuel before filling with fresh fuel. Clean or replace fuel filters if that was not done before winterization.
  • Every few years, on inboard and I/O boats, remove and inspect exhaust manifolds and risers for corrosion.
  • Charge the battery. Clean and tighten electrical connections, especially both ends of battery cables. Use a wire brush on battery terminals, and top off cells with distilled water if applicable.
  • Inspect bilge-ventilation intake and blower ducting for damage or leaks, and run the blower to confirm it works. Test engine warnings and alarms.

Related: outboard four-stroke maintenance, anode selection, marine batteries, battery chargers, engine interval pages including Volvo Penta D6, Yanmar 4JH and Cummins QSB.

Safety equipment and paperwork

BoatUS's spring checklist, with the matching federal rules from the Coast Guard's November 2023 guide:[1][2]

  • Engine cut-off switch. BoatUS notes a law that went into effect in 2021 requiring the operator to use a helm or outboard lanyard, or a wireless cutoff, on certain vessels. Confirm the switch works and the lanyard is serviceable; put fresh batteries in wireless fobs. The Coast Guard guide states that the operator of vessels less than 26 feet shall use the installed engine cut-off switch link while operating on plane or above displacement speed.
  • Visual distress signals. Check dates on pyrotechnic flares. They expire 42 months after manufacture. Expired signals do not count toward the federal carriage requirement, though they may be kept as extras.
  • Fire extinguishers. Inspect them. BoatUS notes a regulation effective 20 April 2022 that requires a 12-year expiration for disposables and has different carriage requirements for older and newer vessels. The Coast Guard guide: inspect seals and tamper indicators, gauges, damage, leakage and clogged nozzles, and replace a non-rechargeable extinguisher 12 years from the date stamped on the bottom (or have a refillable unit serviced). Carry the number required for your length, model year and fixed-system arrangement.
  • Life jackets. Properly sized, wearable jackets in good condition for each passenger, including children. Check inflatable-jacket cylinders and the dissolvable "pill" bobbins in auto-inflating models. Federal rule: one wearable approved PFD per person, readily accessible; a throwable on boats 16 feet and longer (except canoes and kayaks); children under 13 must wear one while underway unless below deck or in an enclosed cabin, unless a state rule differs.
  • Test smoke, carbon monoxide, fume and bilge alarms. Check running lights and spare bulbs. Update chartplotter software. Replenish the first-aid kit. Check that VHF radios work and that the MMSI number is programmed correctly (BoatUS members can obtain a free MMSI at BoatUS.com/MMSI).
  • Get a free vessel safety check from the U.S. Coast Guard Auxiliary or America's Boating Club (U.S. Power Squadrons). BoatUS points to cgaux.org/vsc; the Coast Guard guide also describes the VSC program.

For the dock. In addition to checking the shore-power cable along its length, BoatUS says to check both ends of the cable and the boat's shore-power receptacle for burns, and to test ground-fault protection on the boat and dock.[1]

Paperwork. Make sure registration or documentation is up to date, including trailer tags. Review insurance and provide a copy to the marina or club if required.[1] The Coast Guard guide also covers registration, documentation markings, and when a boating-incident report is required.[2]

Related: life raft servicing, EPIRB registration, VHF, DSC and MMSI, shore power and galvanic isolators.

Sailboat rigging and trailers (if they apply)

BoatUS:[1]

  • Inspect swage fittings for cracks and heavy rust (some discoloration is acceptable). Inspect wire halyards and running backstays for "fishhooks" and rust. Remove tape on turnbuckles, lubricate the threads (BoatUS prefers Teflon), and retape so water can drain. If you suspect a damp core around a chainplate, remove the chainplate to inspect and repair. Inspect masthead sheaves and blocks so they run freely.
  • On trailers: inspect tire treads and sidewalls, check air pressure including the spare, inspect and repack wheel bearings as necessary, test lights, inspect the winch, hitch chains, frame and axle rust, brakes and the brake-fluid reservoir.

After you launch

BoatUS: after the boat is launched, check all thru-hulls for leaks.[1]

Questions

What is the first thing to do after launch?
BoatUS says: check all thru-hulls for leaks.[1] Confirm the drain plug is in before you launch.
How much should a stuffing box drip?
BoatUS says a stuffing box should leak no more than two or three drops each minute when the prop shaft is turning.[1]
When should I replace anodes?
BoatUS's spring checklist says to replace anodes that are more than half wasted away.[1]
Do I need a new fire extinguisher this spring?
Inspect what you have. The Coast Guard's November 2023 guide says a non-rechargeable extinguisher is no longer good after 12 years from the date stamped on the bottom, and that a partially emptied or damaged unit must be replaced or, if refillable, serviced. Carriage counts depend on length, model year and whether a fixed engine-compartment system is installed.[2]
Where can I get a free safety check?
BoatUS and the Coast Guard both point to a Vessel Safety Check from the U.S. Coast Guard Auxiliary or America's Boating Club (U.S. Power Squadrons). See cgaux.org/vsc.[1][2]

Sources

  1. BoatUS, Spring Commissioning Checklist, 2022/v3. https://www.boatus.com/documents/boatus/spring-commissioning-checklist.pdf (opened 16 Nov 2026). BoatUS also points to further how-to articles at BoatUS.com/Spring.
  2. U.S. Coast Guard Boating Safety Division, A Boater's Guide to the Federal Requirements for Recreational Boats, revised November 2023. https://uscgboating.org/assets/1/AssetManager/Boaters-Guide-to-Federal-Requirements-for-Receational-Boats-20231108.pdf (opened 16 Nov 2026).